 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| www.maxim-ic.com DS1602 Elapsed Time Counter PIN ASSIGNMENT RST DQ CLK GND 1 2 3 4 8 7 6 5 VCC X1 X2 VBAT www.maxim-ic.com FEATURES Two 32-bit counters keep track of real-time and elapsed time Counters keep track of seconds for over 125 years Battery powered counter counts seconds from the time battery is attached until VBAT is less than 2.5V VCC powered counter counts seconds while VCC is above VTP and retains the count in the absence of VCC under battery backup power Clear function resets selected counter to 0 Read/write serial port affords low pin count Maximum current drain of less than 1 A from VBAT pin when serial port is disabled One byte protocol defines read/write, counter address and software clear function 8-pin DIP or optional 8-pin SOIC Operating temperature range of -40C to +85C Reduced performance operation down to VCC = 2.5V Underwriters Laboratory (UL) recognized DS1602 8-Pin DIP (300mil) RST DQ CLK GND 1 2 3 4 8 7 6 5 VCC X1 X2 VBAT DS1602 8-Pin SOIC (208mil) Package Dimension Information www.maxim-ic.com/TechSupport/DallasPackInfo.htm PIN DESCRIPTION RST CLK DQ GND X1, X2 VBAT VCC - Reset - Clock - Data Input/Output - Ground - Crystal Inputs - + Battery Input - +5V DESCRIPTION The DS1602 is a real-time clock/elapsed time counter designed to count seconds when V power is CC applied and continually count seconds under battery backup power with an additional counter regardless of the condition of VCC. The continuous counter can be used to derive time of day, week, month, and year by using a software algorithm. The V powered counter will automatically record the amount of time CC that V power is applied. This function is particularly useful in determining the operational time of CC equipment in which the DS1602 is used. Alternatively, this counter can also be used under software control to record real-time eve nts. Communication to and from the DS1602 takes place via a 3-wire serial port. A 1-byte protocol selects read/ write functions, counter clear functions and oscillator trim. A low cost 32.768kHz crystal attaches directly to the X1 and X2 pins. If battery powered-only operation is desired, the VBAT pin must be grounded and the VCC pin must be connected to the battery. Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata. 1 of 10 093002 DS1602 OPERATION The main elements of the DS1602 are shown in Figure 1. As shown, communications to and from the elapsed time counter occur over a 3-wire serial port. The port is activated by driving RST to a high state. With RST at high level, 8 bits are loaded into the protocol shift register providing read/write, register select, register clear, and oscillator trim information. Each bit is serially input on the rising edge of the clock input. After the first eight clock cycles have loaded the protocol register with a valid protocol, additional clocks will output data for a read or input data for a write. VCC must be present to access the DS1602. If V < VTP , the DS1602 goes into a battery backup mode which disables the serial port to CC conserve battery capacity. For battery only operations, the VBAT pin must be grounded and the VCC pin must be connected to the battery. This will keep the DS1602 out of battery backup mode. Battery powered operation down to 2.5V is possible with reduced speed performance on the serial port. The 32bit continuous counter always runs provided that a valid supply is present and the oscillator is enabled. The 32-bit VCC active counter is gated by VCC and the internal 1Hz signal. PROTOCOL REGISTER The protocol bit definition is shown in Figure 2. Valid protocols and the resulting actions are shown in Table 1. Each data transfer to the protocol register designates what action is to occur. As defined, the MSB (bit 7 which is designated ACC) selects the 32-bit continuous counter for access. If ACC is a logical 1 the continuous counter is selected and the 32 clock cycles that follow the protocol will either read or write this counter. If the counter is being read, the contents will be latched into a different register at the end of protocol and the latched contents will be read out on the next 32 clock cycles. This avoids reading garbled data if the counter is clocked by the oscillator during a read. Similarly, if the counter is to be written, the data is buffered in a register and all 32 bits are jammed into the counter simultaneously on the rising edge of the 32nd clock. The next bit (bit 6 which is designated AVC) selects the 32-bit VCC active counter for access. If AVC is a logical 1 this counter is selected and the 32 clock cycles that follow will either read or write this counter. If both bit 7 and bit 6 are written to a logic high, all clock cycles beyond the protocol are ignored and bits 5, 4, and 3 are loaded into the oscillator trim register. A value of binary 3 (011) will give a clock accuracy of 120 seconds per month at +25C. Increasing the binary number towards 7 will cause the real- time clock to run faster. Conversely, lowering the binary number towards 0 will cause the clock to run slower. Binary 000 will stop the oscillator completely. This feature can be used to conserve battery life during storage. In this mode the IBAT current is reduced to 100nA maximum. In applications where oscillator trimming is not practical or not needed, a default setting of 011 is recommended. Bit 2 of protocol (designated CCC) is used to clear the continuous counter. When set to logic 1, the continuous counter will reset to 0 when RST is taken low. Bit 1 of protocol (designated CVC) is used to clear the VCC active counter. When set to logical 1, the VCC active counter will reset to 0 when RST is taken low. Both counters can be reset simultaneously by setting CCC and CVC both to a logical 1. Bit 0 of the protocol (designated RD) determines whether the 32 clocks to follow will write a counter or read a counter. When RD is set to a logical 0 a write action will follow when RD is set to a logical 1 a read action will follow. When sending the protocol, 8 bits should always be sent. Sending less than 8 bits can produce erroneous results. If clearing the counters or trimming the oscillator, the data transfer can be terminated after the 8-bit protocol is sent. However, when reading or writing the counters, 32 clock cycles should always follow the protocol. RESET AND CLOCK CONTROL All data transfers are initiated by driving the RST input high. The RST input has two functions. First, RST turns on the serial port logic, which allows access to the protocol register for the protocol data entry. Second, the RST signal provides a method of terminating the protocol transfer or the 32-bit counter 2 of 8 DS1602 transfer. A clock cycle is a sequence of a rising edge followed by a falling edge. For write inputs, data must be valid during the rising edge of the clock. Data bits are output on the falling edge of the clock when data is being read. All data transfers terminate if the RST input is transitioned low and the DQ pin goes to a high- impedance state. RST should only be transitioned low while the clock is high to avoid disturbing the last bit of data. All data transfers must consist of 8 bits when transferring protocol only or 8 + 32 bits when reading or writing either counter. Data transfer is illustrated in Figure 3. DATA INPUT Following the 8-bit protocol that inputs write mode, 32 bits of data are written to the selected counter on the rising edge of the next 32 CLK cycles. After 32 bits have been entered any additional CLK cycles will be ignored until RST is transitioned low to end data transfer, and then high again to begin new data transfer. DATA OUTPUT Following the eight CLK cycles that input read mode protocol, 32 bits of data will be output from the selected counter on the next 32 CLK cycles. The first data bit to be transmitted from the selected 32-bit counter occurs on the falling edge after the last bit of protocol is written. When transmitting data from the selected 32-bit counter, RST must remain at high level as a transition to low level will terminate data transfer. Data is driven out the DQ pin as long as CLK is low. When CLK is high the DQ pin is tristated. CRYSTAL SELECTION A standard 32.768kHz quartz crystal can be directly connected to the DS1602 via pins 1 and 2 (X1, X2). The crystal selected for use should have a specified load capacitance (C L) of 6pF. For more information on crystal selection and crystal layout considerations, please consult Application Note 58: Crystal Considerations with Dallas Real-Time Clocks. BATTERY SELECTION The battery selected for use with the DS1602 should have an output voltage between 2.5V and 3.5V. A lithium battery of 35mAh or greater will run the elapsed time counter for over 10 years in the absence of power. Small lithium coin cell batteries produce both the proper output voltage and have the capacity to supply the DS1602 for the useable lifetime of the equipment where they are installed. PIN DESCRIPTIONS Vcc, GND - DC power is provided to the device on these pins. VCC is the +5V input. When 5V is applied within normal limits, the device is fully accessible and data can be written and read. When a 3V battery is connected to the device and VCC is below 1.25 x VBAT , reads and writes are inhibited. As VCC falls below VBAT the continuous counter is switched over to the external power supply (nominal 3.0V DC) at VBAT . CLK (Serial Clock Input) - CLK is used to synchronize data movement on the serial interface. DQ (Data Input/Output) - The DQ pin is the bidirectional data pin for the 3-wire interface. RST (Reset) - The reset signal must be asserted high during a read or a write. X1, X2 - Connections for a standard 32.768kHz quartz crystal. The internal oscillator is designed for operation with a crystal having a specified load capacitance of 6pF. For more information on crystal selection and crystal layout considerations, refer to Application Note 58: Crystal Considerations with 3 of 8 DS1602 Dallas Real-Time Clocks. The DS1602 can also be driven by an external 32.768kHz oscillator. In this configuration, the X1 pin is connected to the external oscillator signal and the X2 pin is floated. VBAT - Battery input for any standard 3V lithium cell or other energy source. Battery voltage must be held between 2.5V and 3.5V for proper operation. The nominal write-protect trip-point voltage at which access to the DS1602 is denied is set by the internal circuitry as 1.25 x VBAT nominal. UL recognized to ensure against reverse charging current when used in conjunction with a lithium battery. See "Conditions of Acceptability" at www.maxim- ic.com/TechSupport/QA/ntrl.htm. Figure 1. ELAPSED TIME COUNTER BLOCK DIAGRAM Figure 2. PROTOCOL BIT MAP 7 ACC 6 AVC 5 OSC2 4 OSC1 3 OSC0 2 CCC 1 CVC 0 RD 4 of 8 DS1602 Table 1. VALID PROTOCOLS ACTION ACC AVC OSC2 PROTOCOL OSC1 OSC0 CCC CVC RD FUNCTION Read Continuous Counter 1 0 X X X X X 1 Write Continuous Counter 1 0 X X X X X 0 Read VCC Active Counter 0 1 X X X X X 1 Write VCC Active Counter 0 1 X X X X X 0 Clear Continuous Counter 0 0 X X X 1 X X Clear VCC Active Counter 0 0 X X X X 1 X Set Oscillator Trim Bits X = Don't Care 1 1 A B C X X 0 Output continuous counter on the 32 clocks following protocol. Oscillator trim register is not updated. Counters are not reset. Input data to continuous counter on the 32 clocks following protocol. Oscillator trim register is not updated. Counters are not reset. Output VCC active counter on the 32 clocks following protocol, oscillator trim register is not updated. Counters are not reset. Input data to continuous counter on the 32 clocks following protocol. Oscillator trim register is not updated. Counters are not reset. Resets the continuous counter to all zeros at the end of protocol. Oscillator trim register is not updated. Resets the VCC active counter to all zeros at the end of protocol. Oscillator trim register is not updated. Sets the oscillator trim register to a value of ABC. Counters are unaffected. 5 of 8 DS1602 Figure 3. DATA TRANSFER TIMING DIAGRAM: READ/WRITE DATA TRANSFER Note: tCL, tCH, tR, and tF apply to both read and write data transfer. 6 of 8 DS1602 ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground Operating Temperature Range Storage Temperature Range Soldering Temperature Range -0.3V to +7.0V -40C to +85C -55C to +125C See IPC/JEDEC J-STD-020A This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time can affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Supply Voltage Battery Supply Voltage Logic 1 Input Logic 0 Input SYMBOL VCC VBAT VIH VIL MIN 4.5 2.5 2.0 -0.3 TYP 5.0 3.0 MAX 5.5 3.5 VCC + 0.3 0.8 (-40C to +85C) UNITS V V V V NOTES 1 1 1 1 DC ELECTRICAL CHARACTERISTICS PARAMETER Input Leakage I/O Leakage Logic 1 Output Logic 0 Output Active Supply Current Timekeeping Current Timekeeping Current Leakage Current Battery Trip Point SYMBOL ILI ILO VOH VOL ICC ICC1 IBAT IBATL VTP MIN -1 -1 2.4 (-40C to +85C; VCC = 5V 10%) TYP MAX +1 +1 0.4 1 50 400 100 UNITS A A V V mA A nA nA V NOTES 2 3 4 5, 12 6, 12 11 1.216 x VBAT 1.26 x VBAT 1.285 x VBAT CAPACITANCE PARAMETER Input Capacitance I/O Capacitanc e Crystal Capacitance SYMBOL CI CI/O CX MIN TYP 5 10 6 MAX UNITS pF pF pF (t A = +25C) NOTES 10 7 of 8 DS1602 AC ELECTRICAL CHARACTERISTICS PARAMETER Data to CLK Setup CLK to Data Hold CLK to Data Delay CLK Low Time CLK High Time CLK Frequency CLK Rise and Fall RST to CLK Setup CLK to RST Hold RST Inactive Time RST Low to I/O High-Z CLK High to I/O High- Z SYMBOL tDC tCDH tCDD tCL tCH fCLK tF, tR tCC tCCH tCWH tRDZ tCDZ MIN 50 60 (VCC = +5V 10%; -40C to 85C) TYP MAX UNITS ns ns ns ns ns MHz ns ns ns s ns ns NOTES 7 7 7, 8, 9 7 7 7 7 7 7 7 7 200 250 250 DC 100 60 1 70 20 2.0 500 NOTES: 1) All voltages are referenced to ground. 2) Logic 1 voltages are specified at a source current of 1mA. 3) Logic 0 voltages are specified at a sink current of 4mA. 4) ICC is specified with the DQ pin open. 5) ICC1 is specified with VCC at 5.0V and RST = GND. 6) IBAT is specified with VCC < VBAT and VBAT within DC recommended operating conditions. 7) Measured at VIH = 2.0V or VIL = 0.8V. 8) Measured at VOH = 2.4V or VOL = 0.4V. 9) Load capacitance = 50pF. 10) Specified as the load capacitance for which the crystal frequency is guaranteed (see crystal manufacturer's data sheet). 11) Leakage current is the amount of current consumed from the battery when VCC is not present and the oscillator is turned off. 12) Using a crystal on X1 and X2. 8 of 8 |
Price & Availability of DS1602
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |